HARDWIN 8-1/4 Inch 60T Circular Saw Blade, 5/8 Inch Arbor Fine Finish Blade for Wood, Plywood and MDF

Very nice blade. Placed it in my compound mitre saw to do a couple of test cuts and the cross plywood cut was very impressive. Hardly any tear out as you can see from the pic.

A 60-tooth carbide blade that’s all teeth and hardly any metal? Yes, please! This blade is so lightweight you can hardly believe it can hold all of those very sharp carbide teeth, but it does. And it knows how to use them. And lightweight is almost an understatement…if you have an 8-¼” circular saw I think you might actually notice the weight difference. Although I sadly don’t have a handsaw that fits this diameter blade I plan to use it extensively on my table saw. I expect this blade will be able to rip with less binding than a solid blade and for some reason I do a lot of ripping. But for convenience (because my table saw is buried at the moment) I stuck it on my chop saw to see if ¾” hardwood plywood would faze it. It didn’t. Went through like the proverbial hot knife and left a beautiful clean edge without any extra steps like taping the cut or such. Sixty teeth on that circumference is a lot of teeth and each one has a lot less work to do crashing through the wood compared to fewer-toothed blades. If you do finish work or cabinetry, this is a great blade to have.

This is a solid, well‑built saw blade that made a great first impression and has continued to deliver. I mounted it on my portable table saw for a shed‑building project, and it handled everything I asked of it without hesitation. I used it for cutting furring strips for siding and roofing, as well as ripping thicker pieces like 1x4s and 2x4s. Every cut was smooth and predictable, and the blade never bogged down or wandered.

Even after well over a hundred cuts, it’s still sharp and performing just as consistently as when I first installed it. I haven’t had the chance to run it through any true hardwoods yet, but based on how cleanly it cuts and how true it runs, I’m confident it would hold up just fine there as well.

Overall, this is a dependable, sharp, and sturdy blade—exactly what you want when you’re in the middle of a project and need your tools to just work.

I have a Dewalt portable table saw that takes 8 1/4" blades. Am getting ready to do a bunch of trim work in the house and needed a new blade. This cuts very clean at 60 teeth. Easy to install and works well in my saw and I would recommend it.

I got this blade for a trim project I’m working on using oak lumber. I installed this blade on my ten inch table saw and it has performed flawlessly. The tooth count is perfect for a smoother cut and the kerf of the blade is thin enough to maximize my use of material. I was very surprised to find a sixty tooth saw blade in this price range. The cut outs in the blade help reduce drag when cutting hard materials. This is a nice blade for a reasonable price

Cuts well, perfect for my wood projects. The look and feel of the blade is high quality construction. A bonus, is knowing it works equally well on table saws and if need be, portable cordless saws. Highly recommend.

This 8-1/4 Inch Lightweight Table Saw Blade 60T from HARDWIN makes beautiful thin-kerf cuts in my birch plywood. The teeth are sharp and when you guide the saw straight with no binding, there was no splintering on the top or bottom surfaces. I did notice that my saw spins up a bit faster due to the lighter weight of the blade, but if you encounter any binding, the blade stalls a bit easier due to less momentum of the rotating mass. The coating is good and does tend to resist resin buildup common on uncoated blades. The thin kerf does allow you to make cuts faster due to less material removal, with the additional benefit of less material waste and less sawdust to cleanup. This is one of the few lightweight 8-1/4 inch saw blades that I have found on the market and is reasonably priced at the current $20.56.

*Who needs a 10” saw blade when an 8 1/4” will do just as well? (ALMOST).
*You’ll lose about 7/8” depth of cut with an 8 1/4” blade (2 1/2” vs 3 3/8”), but with a standard 5/8” arbor, it’ll fit practically anything.
*There is a distinct difference however between cross-cut, rip, and combination blades. This is an ATB blade (alternating top bevel) making it ideal for cross cuts.
*The cut-outs on the blade make it ultralight in weight and easy for nearly any job site table saw motor to spin up.
*The kerf width is different depending on where you look, but the blade is labeled 2.0 mm.
*Comes with teeth very nicely protected for worry free storage in your tool box, hung on a nail, or stored in your tool trailer, till needed.
*Shops use pretty much 10” blades and bigger, but for me, this 8 1/4” blade is a super sharp ‘back-up’ for cross-cut work 2 1/2” thick or less.
*Highly recommended.

This Hardwin 8 1/4” saw blade is a professional quality blade and well worth the money. I got this blade to replace the blade on table saw because the old one was beginning to splinter the wood on the bottom each cut due to becoming dull. This Hardwin blade is super sharp, has sixty teeth and leaves a very clean cut. The design of the blade allows it to run cooler without sacrificing strength. I am very happy with this blade and it is well worth the cost.

Hardwin blade for wood. 8.25" with 60 tooth and carbide tips, which is a step up from "cheap" blades. It has a unique design that is supposed to run cooler, definitely interesting. The carbide tips are very sharp and should last quite a while. I plan to use it on an older 9" Craftsman table saw at a later date. I don't have a cordless tool that will run this large of a diameter.

I've been a builder since '87 and I like this blade. It is definitely well made. Back in the day you rarely saw carbide blades and you never saw cut-outs on a blade. Slowly carbide became commonplace and blades started to have some relief slots in them for thermal expansion, but cutouts didn't show up for awhile. The early thin kerf blades would warp and flex as you were pushing them hard. This one does not flex or heat up when you do a deep cut. I only had a piece of pt 6x6 in the shop to try. A hardwood slab will be a good test in the future. I tried some luan afterwards but I could only post one video. It made a smooth cut in the luan with little tear-out. I did mic it up and the body (with the paint) is about .053". The teeth are about .077" The kerf is a little bigger because of the set obviously, but it is definitely thin. I don't have a cordless saw that accepts a 8-1/4" blade, but I'm sure it would spin easier than a "normal" blade. I'll jump in here and update this if it lets me down.

This is an excellent blade for my circular saw. I have had it for many years and have not replaced the blade until now. Honestly, I haven't had to until recently and when I saw this blade, I thought, "Why not give it a try?" I was apprehensive about buying a blade that was under $30 as most of my blades are in the $50 range from one specific company... hint, they are red in color... LOL. But when I saw the design, I thought, maybe it could work. It definitely looks like it will run cooler. I was wrong. This blade runs very cool and rips through plywood and hardwood easily. It has a very thin design as well which means you won't lose as much of your wood as with a traditional blade that is 1/8th inch thick. It is a very solid construction and well worth the price.

Cuts well and quick. Great blade at a good price.

This blade gives great cuts in plywood and some thin walnut that I tested it out on. I also had some cedar scraps from a previous project and the cuts were smooth and sharp in that too. A great thin kerf blade.

Hardwin 8-1/4” 60T blade went straight on my saw and into plywood first. No drama. The cut felt controlled and the saw didn’t bog.Thin kerf is obvious right away, the saw spins up easier and stays there.

I ran it through hardwood next just to see how it behaved. Same story. It stays steady and doesn’t start wandering halfway through the cut. The blade doesn’t heat up fast either, even when pushing through thicker stock. Edges come off looking consistent and ready for the next step, not torn up.

You can tell Hardwin thought about the design. The lighter blade and cutouts help keep things calm while cutting, especially on a cordless saw. Teeth are holding their shape so far and still cutting the same as the first few passes.

One small thing, the markings are a little hard to read once it’s mounted, especially in dim light. That’s about it. For what they cost, this is an easy blade to keep around and keep using.

I replaced the old blade on my table saw with this and what a difference! The old blade was solid and at least twice as thick as this one and would bind up under load. This blade is super sharp, the kerf is super thin and cuts through plywood like butter. With 60 teeth the cuts are also super clean. Makes cutting everything much easier. My old saw is like new again. And at a very good price.

I ordered this for a new circular saw. I'm pleased with the overall quality. The Tungsten Carbide teeth are extremely sharp. I recommend leaving the plastic guard on the teeth until you install the blade on your saw. The blade is definitely lighter than my existing blade which will prolong its life. The rust proof coating is nice given my garage storage area. I also appreciate the narrow kerf. It saves money on bigger projects when you're not cutting 1/8" of the board with each cut.

The main reason I purchased this blade is to take advantage of smooth 60 tooth cuts that don't require extra sanding. Really solid product that I expect will deliver hundreds of cuts.